Clone-A-Willy: 5 Best Penis-Molding Kits

I decided to use a dildo for this kit, and found that it was much easier a penis. As a dildo isn’t attached to a body, it’s much easier to slide into the molding alginate from above. All of the videos online show people doing the kit this way, making it look relatively easy, but it’s a whole lot harder to do with a real person! The dildo also had much more pronounced features that the mold was able to pick up better than with a real penis. That being said, the quality of the finished piece was still pretty poor! You are meant to position the vibrator in the middle of the silicone in the mold, but there is no way of seeing if it’s positioned correctly. In this case, the vibrator sat against the side, meaning there’s a gap where the vibrator shows through. Secondly, the clear silicone already had some semi hard lumps when I mixed it in with the brown silicone and these lumps remained in the final product, meaning there were areas where the silicone hadn’t bonded together and bits could essentially come out of the dildo. Had this not been the case, I think this dildo would have been ok in terms of quality. Lastly, I have no idea why Clone-A-Willy even bother including the vibrators. They win the award for the weakest, buzziest excuses for vibrators that I’ve ever come across. Annoyingly, you have to use them otherwise you won’t have enough silicone to fill your mold, unless you want to buy extra. I do think the process can be fun, but the instructions are so specific and there’s such a precise time limit for the steps that you don’t get a lot of time to enjoy the process with your partner.  

This was our least successful Clone-A-Willy yet! The results were…shockingly bad! I will take some of the responsibility, as I left the cast to dry out for too long, and I think that’s why the texture ended up looking so crazy. However, even before that, we could tell that it wasn’t going to be great! We learned from experience that you cannot put the tube onto your erect penis because the molding alginate spills out. Instead, we tried to dunk my partner’s penis down into the tube, but this left us with a weird shape in the balls department. It was also very hard to prevent his body from touching the side of the plastic, resulting in patches where there was no mold. It was a plus that this kit came with extra molding powder but by this point, we were out of motivation to try again! Leaving the mold to dry for too long before pouring the silicone resulted in a lumpy texture and in places where the mold was thin, like around the base, it peeled away, leaving even more areas with mold. This then meant that the silicone escaped around the sides of the mold, resulting in caped, fleshy nightmare! Another issue we had was with the vibrator. Not only was it a hideous flesh-colored thing with a wired controller and terrible vibrations, but it was also impossible to get it to stay inside the silicone, and it kept floating out. This left us with a vibrator that was sticking half in and half out of the dildo. I think it would be so much easier to get a good mold with a bigger container so there was less risk of hitting the sides. Although, this would of course mean using more materials and companies tend to like keeping that to a minimum!

This kit I did with partner. It was the first one we tried together, and I would say the result was ok but not great! We realised a little too late just how hard it would be to keep an erection while holding your junk in cold goo for 2 mins, so although we did get it back, the mold had already set too much to capture it’s full potential! I was quite impressed by the detail it picked up in the head of the penis. Unfortunately, my partner touched the edge of the tube when making the mold, so there’s a section where the dildo is a bit deformed. As the tube is so slim, it’s very difficult to position your penis without touching the edge. It would be a huge improvement if the tube was bigger so there was less chance of this happening. The dildo also had a lot of rough texture and air bubbles, even though we followed the instructions and tapped it for ages to try and get the bubbles out. I wasn’t impressed enough to try it out but this was our most successful attempt.  Unfortunately, the vibrator was the same terrible battery-powered rubbish as the other kit and couldn’t encourage an inch of excitement out of me! However, I was really impressed by how brightly it glows and it actually startled me when I walked into the dining room in the dark and it was glowing away on the table!

I was actually very excited when it came to my turn! Not so much about the prospect of plunging my bits into the goo but to have a glowing pink homage to my sexuality! I had been brainstorming where I would proudly display my results! I was a disappointed that unlike the Clone-A-Willy kits, this one didn’t come with a thermometer, despite the water needing to be precisely 90 degrees. Luckily, I could use one from the other kits I was reviewing. The molding process actually went really well and I thought it was much easier to position than the Clone-A-Willy kits. Once the mold had set, I was really impressed with how much detail it had picked up and was so excited to pour in the silicone. Unfortunately, as I poured the silicone in, it all pooled in the labia, leaving the clitoris and hood without any covering. I tried to angle the mold to level out the silicone but it didn’t work. The end results left me feeling pretty disappointed as one end is almost completely see through. Again, if there was a bigger tray and more silicone, I think this kit would have worked really well but the kits feel like they are being very stingy with the materials. I thought about ordering some more silicone to use in the mold, but I would have had to buy two refills which would have been really expensive. Plus, mold actually dried up and shrivelled, so I wouldn’t have been able to order them in time for the mold to still be usable. It’s also worth noting that, unlike the other kits, this one doesn’t have any usable functions. I would absolutely love to see this kit as a grinding toy, but that would require more and softer silicone.

The act of making the mold for the sleeve is a bit stressful and time consuming. But, it’s also rewarding for who you are spending time with/for. The act of making this with a partner is both awkward an hilarious and should be approached with an open mind. The harder silicone of the exterior mixed with the more flexible TPE of the internal sleeve made it hard to get fully inserted into The harder silicone of the exterior mixed with the more flexible TPE of the internal sleeve made it hard to get fully inserted into. I found that by removing some of the material around the opening of the TPE sleeve, it was much easier to insert my penis and use. Once you get everything nice and lubed up, the experience goes about like you’d expect. The difference in texture and materials adds a welcome change to some of the other single material masturbators. The internal sleeve texture isn’t anything to write home about but it was satisfactory enough. Overall, I’m extremely happy with the end result of both the creation and testing of my personalized masturbator.